Product Index
Page: 1 2 3 4

EA-Z23-P18   Crankshaft bearing (6001) for Zenoah G-23, G-2D or LH
EA-Z42-P29   Crankshaft for Zenoah G-42
EA-ZLH-P29   Crankshaft for Zenoah LH, (for 8mm wrist pin)
EA-Z23-P17   Crankshaft seal set, large and small, for Zenoah G-23 or LH (12-28-7, 12-22-7)
EA-Z2D-P17   Crankshaft seal set, large and small, for Zenoah G-2D (12-28-7, 12-19-4)
FG-C08   Cut fiberglass .5" strands
FG-C16   Cut fiberglass 1.0" strands
FG-C32   Cut fiberglass 2.0" strands
FG-CS1   Cut fiberglass set, one each of FG-C08, FG-C16 AND FG-C32
TFDS110   Double Skeg Turn Fin, large (1 5/8" deep)
TFDS106   Double Skeg Turn Fin, small (1 3/8" deep)
DH-DDOG8-14   Drive Dog for 1/4" O.D. Prop Shaft, (7/16" O.D.)
DH-DDOG6-12   Drive Dog for 3/16" O.D. Prop Shaft, (3/8" O.D.)
DH-DDOG6-14   Drive Dog for 3/16" O.D. Prop Shaft, (7/16" O.D.)
DH-DDOG6-14SS   Drive Dog for 3/16" O.D. Prop Shaft, (7/16" O.D.)(stainless steel)
WPCA-2   Dual Clamping Water Pickup Assembly
BS-EZ2-56-RC   E/Z connector for #2-56 rod, horizontal screw adjustment for lay down servo (qty 2)
BS-EZ2-56   E/Z connector for #2-56 rod, vertical screw adjustment for stand up servo (qty 2)
BS-EZ4-40-RC   E/Z connector for #4-40 rod, horizontal screw adjustment for lay down servo (qty 2)
BS-EZ4-40   E/Z connector for #4-40 rod, vertical screw adjustment for stand up servo (qty 2)
FS-FP1   E/Z fill fuel pump for fueling your boat or other model
MMG-E02   Echo 21cc & 24cc Motor Mount for 5" rails, 1" Bore (Straight Shaft)
MMG-E01   Echo 21cc & 24cc Motor Mount for 5" rails, 7/8" Bore (GT)
BS-HL   Elastomeric hatch locking system (qty 4)
EA-Z23-P56   Exhaust gasket, for Zenoah G-23 or G-2D
EA-Z26EXH-OR   Exhaust manifold for J&G cylinder to O-Ring style flanged header tube, (outer flange required)
EA-Z23TPA-M   Exhaust manifold, for G-23, O-Ring style water cooled, (Aluminum), use with flanged header tubes
EA-Z23TPAW-M   Exhaust manifold/header, for G-23, wet style water cooled, (Aluminum), 90 degree forward then 180 degree to rear
EA-Z23EPG-P   Exhaust port girdle for Zenoah G-23 or G-2D
FG-TS1   Fiberglass cloth tape set, woven edges, 1", 2", 3" & 4" wide x 20 feet long
FG-T1-20   Fiberglass cloth tape, woven edges, 1" wide x 20 feet long
FG-T2-20   Fiberglass cloth tape, woven edges, 2" wide x 20 feet long
FG-T3-20   Fiberglass cloth tape, woven edges, 3" wide x 20 feet long
FG-T4-20   Fiberglass cloth tape, woven edges, 4" wide x 20 feet long
EA-Z23TPA3-H0   Flanged header pipe for G-23, (Aluminum), 90 degree forward then 180 degree to rear, 0" offset use EA-TPA-H3-0
EA-Z23TPA3-H3   Flanged header pipe for G-23, (Aluminum), 90 degree forward then 180 degree to rear, 3" offset use EA-TPA-H3-3
EA-Z23TPA2L-H   Flanged header pipe for G-23, (Aluminum), 90 degree to rear, long radius, use EA-TPA-H2L
EA-Z23TPA2S-H   Flanged header pipe for G-23, (Aluminum), 90 degree to rear, short radius, use EA-TPA-H2S
EA-Z23TPA1-H   Flanged header pipe for G-23, (Aluminum), wrap to center, use EA-TPA-H1-Z23
H-FSH04-08   Flat socket head screw, #4-40 x 1/2" long, stainless steel, (countersunk) (QTY 5)
H-FSH04-12   Flat socket head screw, #4-40 x 3/4" long, stainless steel, (countersunk) (QTY 5)
H-FSH04-10   Flat socket head screw, #4-40 x 5/8" long, stainless steel, (countersunk) (QTY 5)
H-FW02   Flat washer, #2 x 1/4" O.D., stainless steel (QTY 5)
H-FW08   Flat washer, #8 x 3/8" O.D., stainless steel (QTY 10)
H-FW05F   Flat washers, Fender #5 x 7/16" O.D., stainless steel (fits #4-40 machine & # 6 sheet metal (QTY 5)
H-FW08F   Flat washers, Fender #8 x 3/4" O.D., stainless steel (QTY 5)
FC8-15   Flex Cable 1/4" O.D. x 15" long
FC8-15S   Flex Cable 1/4" O.D. x 15" long, with square on one end
FC8-21   Flex Cable 1/4" O.D. x 21" long
FC8-21S   Flex Cable 1/4" O.D. x 21" long, with square on one end
FC6-18   Flex Cable 3/16" O.D. x 18" long
FC6-18S   Flex Cable 3/16" O.D. x 18" long, with square on one end
FC6-24   Flex Cable 3/16" O.D. x 24" long
FC6-24S   Flex Cable 3/16" O.D. x 24" long, with square on one end
FC5-18   Flex Cable 5/32" O.D. x 18" long
FC5-24   Flex Cable 5/32" O.D. x 24" long
DH-FF8-8-14   Flex Ferrule for 1/4" prop shaft to 1/4" flex cable (brass) (7/16" O.D.)
DH-FF6-8-14   Flex Ferrule for 3/16" prop shaft to 1/4" flex cable (brass) (7/16" O.D.)
DH-FF6-6-12   Flex Ferrule for 3/16" prop shaft to 3/16" flex cable (brass) (3/8" O.D.)
DH-FF6-6-14   Flex Ferrule for 3/16" prop shaft to 3/16" flex cable (brass) (7/16" O.D.)
EA-Z23-P54   Flywheel, for Zenoah G-23
EA-Z42-P54   Flywheel, for Zenoah G-42
STK6-12   For 3/16" drive, 12" long, 1/4" x 9/32" x 12" long, 7/32" x 1/4" x 3" long, (2) 3/16" x 7/32" x 2" long
STK8-12   For 3/16" drive, 12" long, 9/32" x 5/16" x 12" long, 5/16" x 11/32" x 3" long, (2) 1/4" x 9/32" x 2" long
STK6-18   For 3/16" drive, 18" long, 1/4" x 9/32" x 18" long, 7/32" x 1/4" x 3" long, (2) 3/16" x 7/32" x 2" long
STK8-18   For 3/16" drive, 18" long, 9/32" x 5/16" x 18" long, 5/16" x 11/32" x 3" long, (2) 1/4" x 9/32" x 2" long
STK-H35   For Hawk 3.5, 3/16" drive, 1/4" x 9/32" x 13" long stuffing tube, 7/32" x 1/4" x 2" long end sleeve
STK-H75   For Hawk 7.5, 3/16" drive, 1/4" x 9/32" x 15" long stuffing tube, 7/32" x 1/4" x 2" long end sleeve
BS-FLC2   Fuel or water line spring clips, for 1/8" I.D. tubing
BS-FT-SULR12   Fuel tank, 12 oz round-type, Sullivan, 2 1/2" O.D. x 5 5/8" long, for gas use order stopper BS-FT-GS
BS-FT-SULSS12   Fuel tank, 12 oz slant-type, Sullivan, 2 1/8" high x 2 1/2" x 5" long, for gas use order stopper BS-FT-GS
BS-FT-MCC1   Fuel tank, 16 oz McCulloch with cap, 2" high x 3 7/8" x 5 1/2" long, neck protrudes from corner
BS-FT-SULR16   Fuel tank, 16 oz round-type, Sullivan, 3" O.D. x 5 1/2" long, for gas use order stopper BS-FT-GS
BS-FT-SULSS16   Fuel tank, 16 oz slant-type, Sullivan, 2 5/16" high x 2 11/16" x 5 3/4" long, for gas use order stopper BS-FT-GS
BS-FT-SULBT16   Fuel tank, 16 oz V-type, Sullivan, 1 3/4" x 3 7/8" x 5 13/16", for gas use, order stopper BS-FT-GS
BS-FT-HOM1   Fuel tank, 24 oz Homelite with cap, 2 3/4" high x 3" x 7 9/16" long, neck protrudes from end
BS-FT-SULSS24   Fuel tank, 24 oz slant-type, Sullivan, 2 3/8" high x 3" x 7 1/8" long, for gas use order stopper BS-FT-GS
BS-FT-DUB424   Fuel tank, 24 oz square, Dubro, 2 1/2" high x 3 1/16" x 7 1/2" long, for gas use, order stopper BS-FT-GS
BS-FT-SULBT32   Fuel tank, 32 oz special large type, Sullivan, 3" x 3 11/32" x 7 1/2", includes gas and glow stoppers
BS-FT-DUB690   Fuel tank, 32 oz square, Dubro, 3" high x 3 11/16" x 7 3/4" long, includes gas and glow stoppers
BS-FT-SULSS-4   Fuel tank, 4 oz slant-type, Sullivan, 1 3/8" high x 2" x 3 1/2" long, for gas use order stopper BS-FT-GS
BS-FT-SULR-8   Fuel tank, 8 oz round-type, Sullivan, 2 5/16" O.D. x 4 3/16" long, for gas use order stopper BS-FT-GS
BS-FT-SULSS-8   Fuel tank, 8 oz slant-type, Sullivan, 1 7/8" high x 2 1/4" x 4 1/2" long, for gas use order stopper BS-FT-GS
SBFR-_-_   Full range strut, with bearings, See note B1
SAFR-8S   Full Range Strut/T-Bracket 1/4" Sleeve bearings
SAFR-8F   Full Range Strut/T-Bracket 1/4" T-flange bearings
SAFR-6S   Full Range Strut/T-Bracket 3/16" sleeve bearings
SAFR-6F   Full Range Strut/T-Bracket 3/16" T-flange bearings
SAFR-7S   Full Range Strut/T-Bracket 7/32" sleeve bearings
FS-WV01   Garden hose water adapter w/needle valve, for running your water cooled engine at home.
BS-FT-GS   Gas conversion stopper for Dubro & Sullivan fuel tanks, for gasoline
GE-MC25K   Gas Engine, 25cc, Air Cooled, with: mounts, 1/4" square drive, canister muffler, SP throttle linkage
GE-MC25K-CL   Gas Engine, 25cc, Air Cooled, with: mounts, clutch with 1/4" square drive, canister muffler, SP throttle linkage
EA-Z23-P10   Gasket for cylinder to intake manifold/insulator, for Zenoah G-23 or late G-2D
EA-Z42-P10   Gasket for cylinder to intake manifold/insulator, for Zenoah G-42
HK-01   Hardware kit f/Skegs, parallel & angle struts, customer to countersink holes in skeg or strut
BS-HCL   Hatch lock down, Cam-loc push-button fastener and receptacle (qty 1)
BR1222   HBR Master Bracket
BR1222C   HBR Master Bracket, Centerpull option for reduced transom height
HBRCF1410-_-_   HBR Outdrive, centerpull, w/one 4 5/8" long fixed rudder (.40 size) see note B1, W1
HBRCS1410-_-_   HBR Outdrive, centerpull, w/one 4 5/8" long safety shear rudder (.40 size) see note B1, W2
HBRCF1502-_-_   HBR Outdrive, centerpull, w/one 5 1/8" long fixed rudder (.60 size) see note B1, W1
HBRCS1502-_-_   HBR Outdrive, centerpull, w/one 5 1/8" long safety shear rudder (.60 size) see note B1, W2
HBRCF2410-_-_   HBR Outdrive, centerpull, w/two 4 5/8" long fixed rudder (.40 size) see note B1, W1
HBRCS2410-_-_   HBR Outdrive, centerpull, w/two 4 5/8" long safety shear rudder (.40 size) see note B1, W2
HBRCF2502-_-_   HBR Outdrive, centerpull, w/two 5 1/8" long fixed rudder (.60 size) see note B1, W1
HBRCS2502-_-_   HBR Outdrive, centerpull, w/two 5 1/8" long safety shear rudder (.60 size) see note B1, W2
HBRTS1410-_-_   HBR Outdrive, Top Pull, w/one 4 5/8" long safety shear rudder (.40 size) note B1, W2
HBRTS1502-_-_   HBR Outdrive, Top Pull, w/one 5 1/8" long safety shear rudder (.60 size) note B1, W2
HBRTS2410-_-_   HBR Outdrive, Top Pull, w/two 4 5/8" long safety shear rudder (.40 size) note B1, W2
HBRTS2502-_-_   HBR Outdrive, Top Pull, w/two 5 1/8" long safety shear rudder (.60 size) note B1, W2
HBRTF1410-_-_   HBR Outdrive, Top Pull-(1) 4 5/8" long fixed rudder .40 size see note B1, W1
HBRTF1502-_-_   HBR Outdrive, Top Pull-(1) 5 1/8" long fixed rudder .60 size, see note B1, W1
HBRTF2410-_-_   HBR Outdrive, Top Pull-(2) 4 5/8" long fixed rudders .40 size, see note B1, W1
HBRTF2502-_-_   HBR Outdrive, Top Pull-(2) 5 1/8" long fixed rudders .60 size, see note B1, W1
BR1223   HBR Pivot Bracket, 'C' shaped
BR1223M   HBR Pivot Bracket, 'C' shaped, milled and taped to mount to transom
HBR-SOB200   HBR Stand Off Bracket, 2" long, straight
HBR-TSK   HBR Steering kit, Titanium tie rod, marine ball joint rod ends, SS hardware
HBR-SOB200-2U   HBR, Stand off bracket, 2" long, angled 2 degrees up from transom
HBR-SOB200-5U   HBR, Stand off bracket, 2" long, angled 5 degrees up from transom
HBR-SOB250   HBR, Stand off bracket, 2.5" long, straight
HBR-SOB300   HBR, Stand off bracket, 3" long, straight
HBR-SOB400   HBR, Stand off bracket, 4" long, straight
EA-WAL-HSN   High speed needle, finger adjust for Walbro butterfly carburetors
EA-Z23STRTROP   High strength abrasion resistant pull cord
MMG-H02   Homelite 25cc & 30cc Engines with clutch, compact, motor mount for 5" rails
EA-TPA-M-HOM   Homelite 25cc & 30cc Engines, O-ring style water cooled manifold, for flanged header pipes, 7/8" diameter, use EA-HOMTPA-M
EA-TPAW-M-HOM   Homelite 25cc & 30cc Engines, Wet style water cooled manifold/header, use EA-HOMTPAW-M
MMG-H01   Homelite 25cc & 30cc Universal Motor mount for 5" rails, Direct Drive or Clutch
EA-TPA-H1-HOM   Homelite, Flanged header pipe (Aluminum), Wrap to center, 7/8" diameter, use with O-ring style manifold
EA-Z23-P40   Ignition coil (gray), for Zenoah G-23 or G-42
EA-Z23-P40-A   Ignition coil (gray), for Zenoah G-23 or G-42, includes coil, spring and red silicon cap
EA-Z2D-P40-A   Ignition coil, for Zenoah G-2D, includes coil, spring and cap
BS-FF   In tank fuel filter clunk
EA-Z23-P11   Insulator block for intake, for Zenoah G-23 or late G-2D
EA-Z42-P11   Insulator block for intake, for Zenoah G-42
GE-Z26-JMS   J&G 25.6cc Billet top end on Zenoah bottom end, with pro mounts and round collet drive, no clutch, no pipe
GE-Z26-JMC   J&G 25.6cc Billet top end on Zenoah bottom end, with pro mounts and square drive, no clutch, no pipe
GE-Z26-JCS   J&G 25.6cc Billet top end on Zenoah bottom end, with pro mounts, square drive and clutch, no pipe
EA-Z26TOPEND   J&G 25.6cc conversion kit for zenoah G-23: cylinder, button head, sleeve, water jacket, piston, rings, wrist pin, cir-clips
EA-Z23-P36   Key for flywheel, for Zenoah G-23
BS-FKFL   Kwik fill fueling valve for gasoline only, large size
BS-FKF   Kwik fill fueling valve for gasoline only, regular size
BS-LHT   Launch handle, T-style, anodized blue
RS-SWLT   Locking toggle switch with boot kit
EA-Z23-P02   Marine cylinder, stock (2.25 horsepower), for Zenoah G-23 or G-2D
EA-Z23-P02-1   Marine cylinder, with stage 1 modifications, for Zenoah G-23 or G-2D
EA-Z23-P02-2   Marine cylinder, with stage 2 modifications, for Zenoah G-23 or G-2D
EA-Z42-P02-2   Marine cylinder, with stage 2 modifications, for Zenoah G-42
BS-MRRE2-56   Marine replacement rod end #2-56 left or right hand thread (qty 2)
BS-MRRE4-40   Marine replacement rod end #4-40 or 3mm left or right hand thread (qty 2)
BS-MRE2-56   Marine rod end #2-56 thread, with spacer and SS mounting hardware
BS-MRE4-40   Marine rod end #4-40 thread, with spacer and SS mounting hardware
BS-MRES02   Marine rod end spacer for #2-56, 3/16"O.D. x 5/64" tall, brass, (qty 5)
MS1366   Marine Specialties decals, 1 1/2" diameter (slide off type transfer) (qty 5)
MS1367   Marine Specialties monogrammed cap, logo with flags
MS-VL2-_-_   Marine Specialties vinyl stick on graphics (logo with flags, 3 3/8" wide x 1 7/8" tall)(qty 2)
MS-VL4-_-_   Marine Specialties vinyl stick on graphics (logo with flags, 7 1/2" wide x 4 1/4" tall)(qty 2)
MMG-M2502   McCulloch 21cc & 25cc engines, motor mount offset for 5" rails, 1" bore (straight shaft)
MMG-M2501   McCulloch 21cc & 25cc engines, motor mount offset for 5" rails, 7/8" bore
SBMR-6S   Mid range strut, with 3/16" sleeve bearings
SAMR-6S   Mid range strut/T-bracket 3/16" sleeve Bearings
GE-STAGE1   Modified engine, Increased compression, Increased exhaust porting CALL FOR INFORMATION
MMG-U1   Motor Mount Kit for Gas Engine, Universal, Fits 5" Rails, 1" tall angle, 2 kits required
MMG-U2   Motor Mount Kit for Gas Engine, Universal, Fits 5" Rails, 2" tall angle, 2 kits required
MMG-U3   Motor Mount Kit for Gas Engine, Universal, Fits 5" Rails, 3" tall angle, 2 kits required
SK-DUM010   MRS strut & T-bracket, RBFT410-SWP rudder, pivot bracket, pivot pin, nylon flange bushings
SK-DUM011   MRS strut & T-bracket, RBFT502-SWP rudder, pivot bracket, pivot pin, nylon flange bushings
H-NYLN02   Nyloc shakeproof nut, #2-56, stainless steel (qty 5)
H-NYLN04   Nyloc shakeproof nut, #4-40, stainless steel (qty 5)
H-NYLN05   Nyloc shakeproof nut, #5-40, stainless steel (qty 5)
H-NYLN08   Nyloc shakeproof nut, #8-32, stainless steel (qty 5)
H-NYLN-4   Nyloc shakeproof nut, 1/4"-20, stainless steel (qty 5)
B-NFB6   Nylon flange bushing 3/16" I.D. x 15/64" O.D. x 3/16" longf (qty 2)
EA-Z23TPS-ORS   O-Ring set -210S for exhaust header flange to manifold on TPS1 (QD@#) pipe for Zenoah G-23, Silicone
EA-Z23TPS-ORV   O-Ring set -210S for exhaust header flange to manifold on TPS1 (QD@#) pipe for Zenoah G-23, Viton
EA-TPA-ORS   O-Ring set -212S for exhaust header flange to manifold on O-Ring style Aluminum tuned pipes, Silicone
EA-TPA-ORV   O-Ring set -212V for exhaust header flange to manifold O-Ring style Aluminum tuned pipes, Viton
B-OFB8-10-12   Oilite flange bearing 1/4" I.D. x 5/16" O.D. x 1/2" long (7/16" flange O.D.) (qty 2)
B-OFB8-10-16   Oilite flange bearing 1/4" I.D. x 5/16" O.D. x 3/8" long (7/16" flange O.D.) (qty 2)
B-OFB6-10-16   Oilite flange bearing 3/16" I.D. x 5/16" O.D. x 1/2" long (7/16" flange O.D.) (qty 2)
B-OFB6-10-12   Oilite flange bearing 3/16" I.D. x 5/16" O.D. x 3/8" long (7/16" flange O.D.) (qty 2)
B-OSB8-10-16   Oilite sleeve bearing 1/4" I.D. x 5/16" O.D. x 1/2" long (qty 2)
B-OSB8-10-08   Oilite sleeve bearing 1/4" I.D. x 5/16" O.D. x 1/4" long (qty 2)
B-OSB8-10-12   Oilite sleeve bearing 1/4" I.D. x 5/16" O.D. x 3/8" long (qty 2)
B-OSB6-08-16   Oilite sleeve bearing 3/16" I.D. x 1/4" O.D. x 1/2" long (qty 2)
B-OSB6-08-08   Oilite sleeve bearing 3/16" I.D. x 1/4" O.D. x 1/4" long (qty 2)
B-OSB6-10-12   Oilite sleeve bearing 3/16" I.D. x 5/16" O.D. x 3/8" long (qty 2)
B-OSB7-10-12   Oilite sleeve bearing 7/32" I.D. x 5/16" O.D. x 3/8" long (qty 2)
B-OTW8-14-2   Oilite thrust washer 1/4" I.D. x 7/16" O.D. x 1/16" thick (qty 2)
H-PPSMS02-06   Pan head phillips sheet metal screw, #2 x 3/8" long stainless steel (QTY 5)
H-PSORMS08-10   Pan head slotted O-ring seal machine screw, #8-32 x 5/8" long stainless steel (QTY 1)
SBA103-8F   Parallel, 1 3/8" drop, with 1/4" flange bearings
SBP106-8F   Parallel, 1 3/8" drop, with 1/4" flange bearings
SBA103-6F   Parallel, 1 3/8" drop, with 3/16" flange bearings
SBP106-6F   Parallel, 1 3/8" drop, with 3/16" flange bearings
SBA103-6S   Parallel, 1 3/8" drop, with 3/16" sleeve bearings
SBP106-6S   Parallel, 1 3/8" drop, with 3/16" sleeve bearings
SBA100-6S   Parallel, 1" drop, with 3/16" sleeve bearings

Page: 1 2 3 4